金属制品
金屬製品
금속제품
STEEL WIRE PRODUCTS
2015年
3期
29-33
,共5页
在线热处理%酸洗磷化%磷化液%磷化膜
在線熱處理%痠洗燐化%燐化液%燐化膜
재선열처리%산세린화%린화액%린화막
on-line heat treatment%pickling and phosphating%phosphating solution%phosphating film
为适应在线热处理酸洗磷化生产线的需要,酸洗磷化工艺应满足高Dv值(65 mm·m/min)条件下钢丝成膜速度的要求.介绍酸洗磷化的原理,说明总酸度的合理控制是磷化工艺控制的关键.热处理工艺参数确定后,钢丝在线快速磷化控制的关键:一是增加磷化液的有效浓度(总酸度和游离酸度);二是提高磷化槽池的反应温度.通过试验确定的最佳磷化工艺参数:游离酸度10 ~ 18点;总酸度90 ~ 100点;磷化温度85 ~ 95℃;促进剂促进点控制在0.8 ~2.0.按此磷化工艺进行大批量生产,能够满足在线热处理酸洗磷化连续化生产的要求,同时满足后续高速拉拔的要求.
為適應在線熱處理痠洗燐化生產線的需要,痠洗燐化工藝應滿足高Dv值(65 mm·m/min)條件下鋼絲成膜速度的要求.介紹痠洗燐化的原理,說明總痠度的閤理控製是燐化工藝控製的關鍵.熱處理工藝參數確定後,鋼絲在線快速燐化控製的關鍵:一是增加燐化液的有效濃度(總痠度和遊離痠度);二是提高燐化槽池的反應溫度.通過試驗確定的最佳燐化工藝參數:遊離痠度10 ~ 18點;總痠度90 ~ 100點;燐化溫度85 ~ 95℃;促進劑促進點控製在0.8 ~2.0.按此燐化工藝進行大批量生產,能夠滿足在線熱處理痠洗燐化連續化生產的要求,同時滿足後續高速拉拔的要求.
위괄응재선열처리산세린화생산선적수요,산세린화공예응만족고Dv치(65 mm·m/min)조건하강사성막속도적요구.개소산세린화적원리,설명총산도적합리공제시린화공예공제적관건.열처리공예삼수학정후,강사재선쾌속린화공제적관건:일시증가린화액적유효농도(총산도화유리산도);이시제고린화조지적반응온도.통과시험학정적최가린화공예삼수:유리산도10 ~ 18점;총산도90 ~ 100점;린화온도85 ~ 95℃;촉진제촉진점공제재0.8 ~2.0.안차린화공예진행대비량생산,능구만족재선열처리산세린화련속화생산적요구,동시만족후속고속랍발적요구.