铁道科学与工程学报
鐵道科學與工程學報
철도과학여공정학보
JOURNAL OF RAILWAY SCIENCE AND ENGINEERING
2015年
3期
463-474
,共12页
范娟%宋晓东%田利锋%聂志红
範娟%宋曉東%田利鋒%聶誌紅
범연%송효동%전리봉%섭지홍
压实质量连续检测%正交试验设计%变异系数%回归分析
壓實質量連續檢測%正交試驗設計%變異繫數%迴歸分析
압실질량련속검측%정교시험설계%변이계수%회귀분석
continuous compaction check%orthogonal experimental design%coefficient of variation%regression analysis
为定量分析振动压路机工艺参数对压实质量连续检测参数的影响程度,基于正交试验设计原理,以压实质量连续检测指标 CMV 值为研究对象,以振动压路机振幅、振动频率、碾压速度以及行驶方向为影响因素,在沪昆高铁芷江试验段开展压实质量连续检测试验。研究结果表明:振幅、振动频率和碾压速度对 CMV 值的影响高度显著,行驶方向对 CMV 值的影响显著,影响程度依次为振幅>振动频率>碾压速度>行驶方向。根据 CMV 值的变异系数确定使 CMV 值最为稳定的振动压路机压实工艺参数,并以稳定状态下的 CMV 值为基准,建立回归方程,对其他压实工艺参数条件下的 CMV 值进行修正。
為定量分析振動壓路機工藝參數對壓實質量連續檢測參數的影響程度,基于正交試驗設計原理,以壓實質量連續檢測指標 CMV 值為研究對象,以振動壓路機振幅、振動頻率、碾壓速度以及行駛方嚮為影響因素,在滬昆高鐵芷江試驗段開展壓實質量連續檢測試驗。研究結果錶明:振幅、振動頻率和碾壓速度對 CMV 值的影響高度顯著,行駛方嚮對 CMV 值的影響顯著,影響程度依次為振幅>振動頻率>碾壓速度>行駛方嚮。根據 CMV 值的變異繫數確定使 CMV 值最為穩定的振動壓路機壓實工藝參數,併以穩定狀態下的 CMV 值為基準,建立迴歸方程,對其他壓實工藝參數條件下的 CMV 值進行脩正。
위정량분석진동압로궤공예삼수대압실질량련속검측삼수적영향정도,기우정교시험설계원리,이압실질량련속검측지표 CMV 치위연구대상,이진동압로궤진폭、진동빈솔、년압속도이급행사방향위영향인소,재호곤고철지강시험단개전압실질량련속검측시험。연구결과표명:진폭、진동빈솔화년압속도대 CMV 치적영향고도현저,행사방향대 CMV 치적영향현저,영향정도의차위진폭>진동빈솔>년압속도>행사방향。근거 CMV 치적변이계수학정사 CMV 치최위은정적진동압로궤압실공예삼수,병이은정상태하적 CMV 치위기준,건립회귀방정,대기타압실공예삼수조건하적 CMV 치진행수정。
For quantitative analysis of the vibratory compaction technology parameters on the influence degree of con-tinuous compaction measured value ,based on the orthogonal experimental design,CMV was taken as the research ob-ject,the amplitude ,excitation frequency,roller speed and driving direction was selected as the factors;the continu-ous compaction check in Zhijiang construction site of Shanghai -Kunming High -Speed Railway was carried out.The results demonstrate that the amplitude,excitation frequency and roller speed have a highly significant effect on CMV, driving direction has an obvious influence on CMV;and the degree follows by:amplitude >excitation frequency >roll-er speed >driving direction.According to the coefficient of variation of CMV,determining the vibratory compaction technology parameters,which make CMV the most stable;Based on the steady -state CMV,a regression model was established to correct the CMV under the condition of the other vibratory compaction technology parameters.This pa-per provides a new method to improve the stability of the continuous compaction value.