中国有色金属学报(英文版)
中國有色金屬學報(英文版)
중국유색금속학보(영문판)
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA
2015年
6期
2018-2026
,共9页
袁海英%贾成厂%王聪聪%常宇宏%张新新%Bekouche KARIMA%王召利
袁海英%賈成廠%王聰聰%常宇宏%張新新%Bekouche KARIMA%王召利
원해영%가성엄%왕총총%상우굉%장신신%Bekouche KARIMA%왕소리
多孔Al-Cu合金%非水基凝胶注模%工艺参数%裂纹%气孔
多孔Al-Cu閤金%非水基凝膠註模%工藝參數%裂紋%氣孔
다공Al-Cu합금%비수기응효주모%공예삼수%렬문%기공
porous Al-Cu alloy%non-aqueous gelcasting%process conditions%crack%pore
通过凝胶注模工艺制备多孔铝铜合金。研究凝胶注模工艺参数如单体含量、交联剂与单体的比例、分散剂和引发体系4个因素对坯体高度、固化时间和坯体品质3个指标的影响。其中分散剂对坯体高度,单体对坯体质量的影响最大。通过分析得出最佳工艺为:单体体积分数10%、交联剂体积分数2%、引发剂体积分数0.2%、分散剂质量1.2 g,在此条件下坯体呈现最好的品质。同时探讨工艺参数消除裂纹和形成孔结构的机理。利用压汞法得出孔直径在10~10000 nm范围内,开孔气孔率达到38.78%。
通過凝膠註模工藝製備多孔鋁銅閤金。研究凝膠註模工藝參數如單體含量、交聯劑與單體的比例、分散劑和引髮體繫4箇因素對坯體高度、固化時間和坯體品質3箇指標的影響。其中分散劑對坯體高度,單體對坯體質量的影響最大。通過分析得齣最佳工藝為:單體體積分數10%、交聯劑體積分數2%、引髮劑體積分數0.2%、分散劑質量1.2 g,在此條件下坯體呈現最好的品質。同時探討工藝參數消除裂紋和形成孔結構的機理。利用壓汞法得齣孔直徑在10~10000 nm範圍內,開孔氣孔率達到38.78%。
통과응효주모공예제비다공려동합금。연구응효주모공예삼수여단체함량、교련제여단체적비례、분산제화인발체계4개인소대배체고도、고화시간화배체품질3개지표적영향。기중분산제대배체고도,단체대배체질량적영향최대。통과분석득출최가공예위:단체체적분수10%、교련제체적분수2%、인발제체적분수0.2%、분산제질량1.2 g,재차조건하배체정현최호적품질。동시탐토공예삼수소제렬문화형성공결구적궤리。이용압홍법득출공직경재10~10000 nm범위내,개공기공솔체도38.78%。
The porous Al?Cu alloy was prepared by the gelcasting process. And the effects of gelcasting conditions, such as monomer, the volume ratio of cross-linker and monomer, dispersant and redox initiating system on the height, gelling time and the quality of green body were investigated. (It was found that the dispersant and monomer played significant roles in the height and quality of green bodies, respectively.) The optimal conditions were 10% monomer, 2% cross-linker, 0.2% initiator (volume fraction), and 1.2 g dispersant, in which the green body exhibited the best quality. The mechanisms of process conditions in eliminating the cracks and forming the pores of in the five stages were proposed. Mercury porosimetry provided a description of pore diameter ranging from 10 to 10000 nm and open porosity of 38.78 %.