金刚石与磨料磨具工程
金剛石與磨料磨具工程
금강석여마료마구공정
DIAMOND & ABRASIVES ENGINNERING
2015年
4期
41-46
,共6页
叶鲁浩%王志%张进生%黄波%鞠军伟%高丽君%高克祥%于家伟
葉魯浩%王誌%張進生%黃波%鞠軍偉%高麗君%高剋祥%于傢偉
협로호%왕지%장진생%황파%국군위%고려군%고극상%우가위
圆锯片%振动%模态分析%谐响应分析
圓鋸片%振動%模態分析%諧響應分析
원거편%진동%모태분석%해향응분석
circular saw blade%vibration%modal analysis%harmonic response analysis
针对?2482 mm 圆锯片使用过程中出现散射状与蝌蚪状裂纹的现象,基于 ANSYS 对圆锯片进行模态分析及谐响应分析。研究表明:在700~840 Hz(即300~360 r/min)频率范围内,锯片的相邻固有频率之间的差值较小,易发生共振效应;轴孔处与距轴孔1/3~2/3圆周处的振动幅度较大,可通过在锯片轴孔两侧固定夹盘或在距轴孔1/3~2/3圆周处滚压处理减小弯曲裂纹。通过对圆锯片的谐响应分析,计算出:锯片在775~800 Hz 及725 Hz 时发生共振效应;在800 Hz 附近出现应力主峰,是产生疲劳裂纹的主要原因。为了避开共振敏感区域,推荐锯片工作转速范围为317~330 r/min、348~360 r/min。
針對?2482 mm 圓鋸片使用過程中齣現散射狀與蝌蚪狀裂紋的現象,基于 ANSYS 對圓鋸片進行模態分析及諧響應分析。研究錶明:在700~840 Hz(即300~360 r/min)頻率範圍內,鋸片的相鄰固有頻率之間的差值較小,易髮生共振效應;軸孔處與距軸孔1/3~2/3圓週處的振動幅度較大,可通過在鋸片軸孔兩側固定夾盤或在距軸孔1/3~2/3圓週處滾壓處理減小彎麯裂紋。通過對圓鋸片的諧響應分析,計算齣:鋸片在775~800 Hz 及725 Hz 時髮生共振效應;在800 Hz 附近齣現應力主峰,是產生疲勞裂紋的主要原因。為瞭避開共振敏感區域,推薦鋸片工作轉速範圍為317~330 r/min、348~360 r/min。
침대?2482 mm 원거편사용과정중출현산사상여과두상렬문적현상,기우 ANSYS 대원거편진행모태분석급해향응분석。연구표명:재700~840 Hz(즉300~360 r/min)빈솔범위내,거편적상린고유빈솔지간적차치교소,역발생공진효응;축공처여거축공1/3~2/3원주처적진동폭도교대,가통과재거편축공량측고정협반혹재거축공1/3~2/3원주처곤압처리감소만곡렬문。통과대원거편적해향응분석,계산출:거편재775~800 Hz 급725 Hz 시발생공진효응;재800 Hz 부근출현응력주봉,시산생피로렬문적주요원인。위료피개공진민감구역,추천거편공작전속범위위317~330 r/min、348~360 r/min。
Widely scattered and tadpole-like cracks appeared on? 2482 mm circular saw blade during sawing.Circular saw blade modal analysis and harmonic response analysis were carried out based on ANSYS.The results showed that the difference of circular saw blade' s natural frequency was small among 700 —840 Hz(300 —360 r∕min),which easily led to resonance effects.The vibration amplitude was lager in axis hole and 1∕3 to 2∕3 circumference from the hole.To reduce the bending crack,it was good to fix chuck on both sides of the blade or press along the 1∕3 to 2∕3 circumference from the hole. It was calculated that the circular saw blade’s resonance effects occurred at 775 —800 Hz and 725 Hz and a stress peak appeared at 800 Hz,which might be the main reason for fatigue crack.So as to avoid the resonance sensitive areas when using the circular saw blade,the blade working speed should be 317—330 r∕min or 348—360 r∕min.