CAJ | 학술논문

该文以研究光皮树果实冷榨制油过程中的流变特性为目标，利用自制直筒式压榨试验装置进行不同压榨应变水平的应力松弛试验，基于岩石流变基本模型分段模拟应力应变关系，建立其流变模型并进行验证。结果表明：光皮树果实加载过程中应力应变关系呈现线性和非线性两部分，屈服应变为0.4，应力松弛量随着压榨应变的增大而增大。采用分段模拟建模分析，并确定相应的模型参数。首先利用弹性元件和阻尼器模组合而成的广义Maxwell模型模拟线性段松弛过程，再利用线性与川北公夫模型叠加共同模拟非线性段松弛过程，构建了直筒式冷态压榨的流变模型，并进行了参数求解。误差分析表明：应变为0.5时，相对误差较大；而实际压榨过程中光皮树果实压榨应变均大于0.55，在此段应变范围内的模型平均相对误差均在7%之内，因此该模型为研究光皮树果实直筒式冷态压榨设备时应力应变参数的选取提供基础数据。
해문이연구광피수과실랭자제유과정중적류변특성위목표，이용자제직통식압자시험장치진행불동압자응변수평적응력송이시험，기우암석류변기본모형분단모의응력응변관계，건립기류변모형병진행험증。결과표명：광피수과실가재과정중응력응변관계정현선성화비선성량부분，굴복응변위0.4，응력송이량수착압자응변적증대이증대。채용분단모의건모분석，병학정상응적모형삼수。수선이용탄성원건화조니기모조합이성적엄의Maxwell모형모의선성단송이과정，재이용선성여천북공부모형첩가공동모의비선성단송이과정，구건료직통식랭태압자적류변모형，병진행료삼수구해。오차분석표명：응변위0.5시，상대오차교대；이실제압자과정중광피수과실압자응변균대우0.55，재차단응변범위내적모형평균상대오차균재7%지내，인차해모형위연구광피수과실직통식랭태압자설비시응력응변삼수적선취제공기출수거。
Swida wilsoniana is one of the important woody oil plants supported by the State Council, mainly distributed in Hunan, Guizhou and Jiangxi Province, of which the whole fruits contain about 30% oils with high nutritional value. Mechanical pressing and solvent extraction are 2 major ways for fruit oil, and the lack of equipment for Swida wilsoniana fruits with the characteristics of hard core make it imperative to carry out this work. In order to study the rheological property of Swida wilsoniana fruits in cold pressing process, the stress relaxation tests under different loading strain levels were carried out by using the self-made straight cylinder pressing device. Based on the basic model of rock rheology, the relationship between the stress and strain was simulated, and its rheological model was established. The results showed that the relationship of stress and strain in the loading process of Swida wilsoniana fruits was divided into 2 parts which were defined as linear period and nonlinear period, and the critical yield strain was 0.4, meaning that the relationship between stress and strain was linear when the strain level was lower than 0.4 and was nonlinear as strain level was higher than 0.4. The amount of stress relaxation rose with the increase of pressing strain level, especially as the strain level was higher than 0.5, due to the oil bursting out of oilseeds, and the higher strain levels, the greater amount of oil, and the greater amount of stress relaxation. Segmented simulation was used to analyze and determine the parameters of the model. Firstly, the Maxwell model generalized by elastic element and damper mode was used to simulate the linear relaxation process. Then linear mode and the Kawakita's superposition model jointly simulated the process of nonlinear relaxation. Finally the rheological model was established and the parameters were obtained. Error analysis showed the application range and simulation effect. The relative error was large when the strain was 0.5 due to the rupture occurring in the period of loading, and the average relative errors were less than 7%when the strains were larger than 0.55, which could provide basic data of stress and strain parameters for squeezing process and special equipment. However, pressing pressure was only one of the pressing factors which would affect the pressing effect for Swida wilsoniana fruits. Other factors such as form of oilseeds, composition of main contents, pressing speed and temperature were also important factors influencing squeezing effect. Morphological change of Swida wilsoniana fruits was just a reflection for pressing, which had some limitations. The main evaluation index for pressing effect was the oil yield rate or residual oil of cake. So establishing the relationship between stress, strain and residual oil was an important direction of research. Therefore, a comprehensive analysis of the impact of various factors should be considered to establish an appropriate system for oilseed processing conditions, and to realize a cold and effective pressing technique for oil Swida wilsoniana fruits.