车用发动机
車用髮動機
차용발동궤
2015年
4期
85-88
,共4页
燃油压力脉动%仿真%缓冲器%噪声
燃油壓力脈動%倣真%緩遲器%譟聲
연유압력맥동%방진%완충기%조성
fuel pressure pulsation%simulation%damper%noise
针对某乘用车开发过程中出现的怠速低频噪声进行了研究 ,发现噪声源为汽油机喷油器反复开启产生的燃油压力脉动.应用商业流体软件对喷油器关闭瞬间燃油在油轨内的传播过程进行三维仿真 ,得到油轨内的油压变化规律.并在原机模型的基础上分析了油轨尺寸和横截面积的变化对油压的影响.分析表明 :油轨横截面面积加大对油压脉动有一定的降低作用 ;相同横截面积条件下 ,长宽比越大 ,抑制油压脉动的效果越好.优化方案的噪声测试结果表明 ,方轨比圆轨的噪声小 ,但圆轨带内置缓冲器 ,效果最佳 ,可降低车内噪声3 .2 dB.
針對某乘用車開髮過程中齣現的怠速低頻譟聲進行瞭研究 ,髮現譟聲源為汽油機噴油器反複開啟產生的燃油壓力脈動.應用商業流體軟件對噴油器關閉瞬間燃油在油軌內的傳播過程進行三維倣真 ,得到油軌內的油壓變化規律.併在原機模型的基礎上分析瞭油軌呎吋和橫截麵積的變化對油壓的影響.分析錶明 :油軌橫截麵麵積加大對油壓脈動有一定的降低作用 ;相同橫截麵積條件下 ,長寬比越大 ,抑製油壓脈動的效果越好.優化方案的譟聲測試結果錶明 ,方軌比圓軌的譟聲小 ,但圓軌帶內置緩遲器 ,效果最佳 ,可降低車內譟聲3 .2 dB.
침대모승용차개발과정중출현적태속저빈조성진행료연구 ,발현조성원위기유궤분유기반복개계산생적연유압력맥동.응용상업류체연건대분유기관폐순간연유재유궤내적전파과정진행삼유방진 ,득도유궤내적유압변화규률.병재원궤모형적기출상분석료유궤척촌화횡절면적적변화대유압적영향.분석표명 :유궤횡절면면적가대대유압맥동유일정적강저작용 ;상동횡절면적조건하 ,장관비월대 ,억제유압맥동적효과월호.우화방안적조성측시결과표명 ,방궤비원궤적조성소 ,단원궤대내치완충기 ,효과최가 ,가강저차내조성3 .2 dB.
The low frequency noise at idle speed for a passenger car was researched and it was found that the noise source was the fuel pulsation produced by the repeated opening of gasoline injector .Commercial fluid software was applied to simulate the pressure pulsation in fuel rail at the closing moment of gasoline injector and the fuel pressure variation law was acquired .Based on the original model ,the effects of fuel rail size and cross section on fuel pressure were researched .The results show that in-creased cross section of fuel rail can suppress the fuel pressure pulsation to a certain extent .The fuel rail with a large length/width ratio has better effect at the same cross section .In addition ,the square rail has less noise than the circular rail .Howev-er ,the circular rail with inner damper has better effect and could decrease vehicle noise by 3 .2 dB .