制造技术与机床
製造技術與機床
제조기술여궤상
MANUFACTURING TECHNOLOGY & MACHINE TOOL
2015年
8期
114-117
,共4页
焦安源%李宗泽%全洪军%陈燕
焦安源%李宗澤%全洪軍%陳燕
초안원%리종택%전홍군%진연
磁力研磨%表面粗糙度%内环槽%同步光整
磁力研磨%錶麵粗糙度%內環槽%同步光整
자력연마%표면조조도%내배조%동보광정
magnetic abrasive finishing%surface roughness%inner ring%groove synchronous finishing
液压系统中常常需要大量内环槽密封结构件,由于尺寸小、加工空间有限,传统研磨工艺难以有效对其表面进行光整加工.结合磁力研磨法的原理及特点提出采用该方法对工件内环槽表面进行实验加工,并总结了内环槽磁力研磨光整的基本工艺参数,经过60rain研磨加工后,内环槽两侧面平均表面粗糙度可由Ra3.47 μm降至Ra0.63 μm,底面的粗糙度也可由Ra3.25 μm降至Ra0.70um,且通过微观表面观察发现原始加工纹理得到了有效去除.结果表明,基于磁力研磨法,采用磁石直接吸附磁性磨料,与内环槽各个表面均保持1ram间隙进行光整时,可以实现对内环槽3个面的同步光整加工.
液壓繫統中常常需要大量內環槽密封結構件,由于呎吋小、加工空間有限,傳統研磨工藝難以有效對其錶麵進行光整加工.結閤磁力研磨法的原理及特點提齣採用該方法對工件內環槽錶麵進行實驗加工,併總結瞭內環槽磁力研磨光整的基本工藝參數,經過60rain研磨加工後,內環槽兩側麵平均錶麵粗糙度可由Ra3.47 μm降至Ra0.63 μm,底麵的粗糙度也可由Ra3.25 μm降至Ra0.70um,且通過微觀錶麵觀察髮現原始加工紋理得到瞭有效去除.結果錶明,基于磁力研磨法,採用磁石直接吸附磁性磨料,與內環槽各箇錶麵均保持1ram間隙進行光整時,可以實現對內環槽3箇麵的同步光整加工.
액압계통중상상수요대량내배조밀봉결구건,유우척촌소、가공공간유한,전통연마공예난이유효대기표면진행광정가공.결합자력연마법적원리급특점제출채용해방법대공건내배조표면진행실험가공,병총결료내배조자력연마광정적기본공예삼수,경과60rain연마가공후,내배조량측면평균표면조조도가유Ra3.47 μm강지Ra0.63 μm,저면적조조도야가유Ra3.25 μm강지Ra0.70um,차통과미관표면관찰발현원시가공문리득도료유효거제.결과표명,기우자력연마법,채용자석직접흡부자성마료,여내배조각개표면균보지1ram간극진행광정시,가이실현대내배조3개면적동보광정가공.