土木工程与管理学报
土木工程與管理學報
토목공정여관이학보
JOURNAL OF HUAZHONG UNIVERSITY OF SCIENCE AND TECHNOLOGY·URBAN SCIENCE
2015年
3期
11-15,21
,共6页
高飞%黄世涛%梅世龙%周大庆
高飛%黃世濤%梅世龍%週大慶
고비%황세도%매세룡%주대경
梁柱节点模型%HRB500E%本构模型%数值模拟
樑柱節點模型%HRB500E%本構模型%數值模擬
량주절점모형%HRB500E%본구모형%수치모의
beam-column joint model%HRB500 E%constitutive model%numerical simulation
本文采用超级节点模型模拟配置HRB500E钢筋梁柱节点在低周反复荷载作用下的非线性反应。基于OpenSees软件编写了分析程序,该程序选取Beam-Column Joint单元及合适的材料本构模型,并利用修正斜压场理论( MCFT)确定节点核心区的参数。 MCFT定参通过自编Matlab算例实现。通过OpenSees软件对3个配置HRB500E钢筋梁柱节点试件进行数值模拟,得到试件梁端的荷载-位移曲线。通过与试验结果对比发现,两者的滞回曲线吻合良好,具体表现为滞回曲线最大荷载误差较小、滞回环峰值荷载走势较一致,并且捏缩效应也较一致。
本文採用超級節點模型模擬配置HRB500E鋼觔樑柱節點在低週反複荷載作用下的非線性反應。基于OpenSees軟件編寫瞭分析程序,該程序選取Beam-Column Joint單元及閤適的材料本構模型,併利用脩正斜壓場理論( MCFT)確定節點覈心區的參數。 MCFT定參通過自編Matlab算例實現。通過OpenSees軟件對3箇配置HRB500E鋼觔樑柱節點試件進行數值模擬,得到試件樑耑的荷載-位移麯線。通過與試驗結果對比髮現,兩者的滯迴麯線吻閤良好,具體錶現為滯迴麯線最大荷載誤差較小、滯迴環峰值荷載走勢較一緻,併且捏縮效應也較一緻。
본문채용초급절점모형모의배치HRB500E강근량주절점재저주반복하재작용하적비선성반응。기우OpenSees연건편사료분석정서,해정서선취Beam-Column Joint단원급합괄적재료본구모형,병이용수정사압장이론( MCFT)학정절점핵심구적삼수。 MCFT정삼통과자편Matlab산례실현。통과OpenSees연건대3개배치HRB500E강근량주절점시건진행수치모의,득도시건량단적하재-위이곡선。통과여시험결과대비발현,량자적체회곡선문합량호,구체표현위체회곡선최대하재오차교소、체회배봉치하재주세교일치,병차날축효응야교일치。
The super beam-column joint model is adopted to simulate the nonlinear response of beam-column joint with HRB500E reinforced bar under low cyclic loading. An analysis program is edited based on finite element ( FE) software OpenSees. This program adopts the Beam-Column Joint element and suitable material constitutive models. The parameters of the shear panel are determined by the Modified Compression-Filed Theory ( MCFT) . A matlab program based the MCFT is used to determine the shear capacity of the shear panel. Three beam-column joint specimens with HRB500E reinforcements are simulated by OpenSees for the verification and calibration of FE method. For the comparison of hysteretic behaviors between the experiment and numerical analysis, the hysteretic curves show a reasonable agreement with small difference of ultimate capacity, coincident peak loads of hysteretic loops as well as similar pinching effects.