中国造纸
中國造紙
중국조지
China Pulp & Paper
2015年
8期
7-12
,共6页
唐爱民%李德贵%赵姗%贾超锋
唐愛民%李德貴%趙姍%賈超鋒
당애민%리덕귀%조산%가초봉
聚酰亚胺树脂%对位芳纶纸%浸渍工艺%最佳浓度
聚酰亞胺樹脂%對位芳綸紙%浸漬工藝%最佳濃度
취선아알수지%대위방륜지%침지공예%최가농도
polyimide resin%PPTA paper%impregnation process%optimum concentration
通过采用红外光谱、DSC-TG分析手段对4种聚酰亚胺树脂(PM1~PM4)的结构和热稳定性进行了分析;用聚酰亚胺树脂浸渍对位芳纶原纸,考察聚酰亚胺树脂的上胶量对对位芳伦纸强度性能的影响以及对位芳纶原纸与4种浸渍树脂的相容性.结果表明,PM1树脂的酰胺化程度较高,为带有胺端基芳香族聚酰亚胺,与对位芳纶分子结构相近,因此与对位芳纶原纸的相容性最好;聚酰亚胺树脂的上胶量随着树脂浸渍液质量分数的增大而升高,当PM1树脂浸渍液质量分数25%时,其上胶量达36.68%,对位芳纶纸的抗张指数为52.4 N·m/g,伸长率为0.8%,撕裂指数为43.1 N·m2/g,此时对位芳纶纸的强度性能最为理想.
通過採用紅外光譜、DSC-TG分析手段對4種聚酰亞胺樹脂(PM1~PM4)的結構和熱穩定性進行瞭分析;用聚酰亞胺樹脂浸漬對位芳綸原紙,攷察聚酰亞胺樹脂的上膠量對對位芳倫紙彊度性能的影響以及對位芳綸原紙與4種浸漬樹脂的相容性.結果錶明,PM1樹脂的酰胺化程度較高,為帶有胺耑基芳香族聚酰亞胺,與對位芳綸分子結構相近,因此與對位芳綸原紙的相容性最好;聚酰亞胺樹脂的上膠量隨著樹脂浸漬液質量分數的增大而升高,噹PM1樹脂浸漬液質量分數25%時,其上膠量達36.68%,對位芳綸紙的抗張指數為52.4 N·m/g,伸長率為0.8%,撕裂指數為43.1 N·m2/g,此時對位芳綸紙的彊度性能最為理想.
통과채용홍외광보、DSC-TG분석수단대4충취선아알수지(PM1~PM4)적결구화열은정성진행료분석;용취선아알수지침지대위방륜원지,고찰취선아알수지적상효량대대위방륜지강도성능적영향이급대위방륜원지여4충침지수지적상용성.결과표명,PM1수지적선알화정도교고,위대유알단기방향족취선아알,여대위방륜분자결구상근,인차여대위방륜원지적상용성최호;취선아알수지적상효량수착수지침지액질량분수적증대이승고,당PM1수지침지액질량분수25%시,기상효량체36.68%,대위방륜지적항장지수위52.4 N·m/g,신장솔위0.8%,시렬지수위43.1 N·m2/g,차시대위방륜지적강도성능최위이상.