焊管
銲管
한관
Welded Pipe and Tube
2015年
8期
42-45
,共4页
周书亮%邓志伟%谷海龙%魏婷%于振宁%廖洪
週書亮%鄧誌偉%穀海龍%魏婷%于振寧%廖洪
주서량%산지위%곡해룡%위정%우진저%료홍
螺旋焊管生产机组%递送机%同步%通讯%控制器%上位机
螺鏇銲管生產機組%遞送機%同步%通訊%控製器%上位機
라선한관생산궤조%체송궤%동보%통신%공제기%상위궤
SAWH pipe production unit%delivery machine%synchronization%communication%controller%upper computer
针对螺旋焊管生产机组在生产过程中出现的递送机上下辊不同步运行造成的顿板和烧穿问题,设计了一拖二控制系统。该系统以 Profibus DP 方式与 PLC 主站通讯,通过 Starter 软件对SINAMICS DCM 6RA80控制器进行参数设置和PLC程序运算处理,实现1台控制器对上下辊电机同步控制。上位机采用CP5711连接到PLC主站,对运行参数进行监控。实际运行表明,递送机速度误差为±0.02 m/min,满足生产工艺要求,系统运行同步、稳定。
針對螺鏇銲管生產機組在生產過程中齣現的遞送機上下輥不同步運行造成的頓闆和燒穿問題,設計瞭一拖二控製繫統。該繫統以 Profibus DP 方式與 PLC 主站通訊,通過 Starter 軟件對SINAMICS DCM 6RA80控製器進行參數設置和PLC程序運算處理,實現1檯控製器對上下輥電機同步控製。上位機採用CP5711連接到PLC主站,對運行參數進行鑑控。實際運行錶明,遞送機速度誤差為±0.02 m/min,滿足生產工藝要求,繫統運行同步、穩定。
침대라선한관생산궤조재생산과정중출현적체송궤상하곤불동보운행조성적돈판화소천문제,설계료일타이공제계통。해계통이 Profibus DP 방식여 PLC 주참통신,통과 Starter 연건대SINAMICS DCM 6RA80공제기진행삼수설치화PLC정서운산처리,실현1태공제기대상하곤전궤동보공제。상위궤채용CP5711련접도PLC주참,대운행삼수진행감공。실제운행표명,체송궤속도오차위±0.02 m/min,만족생산공예요구,계통운행동보、은정。
Aim at the problems of pausing plate and burning through during SAWH pipe production course, which caused by the reason that the up and down rollers of delivery machine are not synchronous, a kind of one-to-two control system was designed. This system communicates with PLC master station in Profibus DP mode, through the parameter setting of Starter software on the SINAMICS DCM 6RA80 controller and the processing of PLC program operation, the goal that one controller synchronously controls two motors of up and down rollers comes ture. The upper computer was connected to PLC master station through CP5711, and monitors the running parameters. Actual operation shows that delivery machine speed error is ±0.02 m/min, meet the requirements of production process, and the operation is synchronous and stable.