火力与指挥控制
火力與指揮控製
화력여지휘공제
Fire Control & Command Control
2015年
8期
27-32
,共6页
王士岩%王星%王洪迅%汪欣
王士巖%王星%王洪迅%汪訢
왕사암%왕성%왕홍신%왕흔
瞬时测频%线性调频信号%信号交叠的频率分离%ADC
瞬時測頻%線性調頻信號%信號交疊的頻率分離%ADC
순시측빈%선성조빈신호%신호교첩적빈솔분리%ADC
instantaneous frequency measurement%LFM signal%separation of the overlapping signals frequency%ADC
线性调频信号是脉冲压缩雷达中一种重要的脉冲压缩雷达信号,但当前的瞬时测频系统无法对其检测,更无法检测交叠信号.以瞬时测频系统为基础,分析了单线性调频信号和交叠线性调频经过瞬时测频系统的理论输出,据此提出了一种改进IFM系统的思路和解算交叠线性调频信号方法.新方法用模数转换器(ADC)对前沿未交叠的I、Q输出值进行量化和连续时间采样,得到一个信号离散频率值,应用LMS算法估计出其初始频率和调频斜率.以此为基础,根据交叠部分的I、Q输出值,估计出另一个信号参数.由Matlab/Simulink仿真验证可知,新方法能够估计两交叠线性调频信号的参数.
線性調頻信號是脈遲壓縮雷達中一種重要的脈遲壓縮雷達信號,但噹前的瞬時測頻繫統無法對其檢測,更無法檢測交疊信號.以瞬時測頻繫統為基礎,分析瞭單線性調頻信號和交疊線性調頻經過瞬時測頻繫統的理論輸齣,據此提齣瞭一種改進IFM繫統的思路和解算交疊線性調頻信號方法.新方法用模數轉換器(ADC)對前沿未交疊的I、Q輸齣值進行量化和連續時間採樣,得到一箇信號離散頻率值,應用LMS算法估計齣其初始頻率和調頻斜率.以此為基礎,根據交疊部分的I、Q輸齣值,估計齣另一箇信號參數.由Matlab/Simulink倣真驗證可知,新方法能夠估計兩交疊線性調頻信號的參數.
선성조빈신호시맥충압축뢰체중일충중요적맥충압축뢰체신호,단당전적순시측빈계통무법대기검측,경무법검측교첩신호.이순시측빈계통위기출,분석료단선성조빈신호화교첩선성조빈경과순시측빈계통적이론수출,거차제출료일충개진IFM계통적사로화해산교첩선성조빈신호방법.신방법용모수전환기(ADC)대전연미교첩적I、Q수출치진행양화화련속시간채양,득도일개신호리산빈솔치,응용LMS산법고계출기초시빈솔화조빈사솔.이차위기출,근거교첩부분적I、Q수출치,고계출령일개신호삼수.유Matlab/Simulink방진험증가지,신방법능구고계량교첩선성조빈신호적삼수.
Linear Frequency Modulation (LFM) signals is an important intra-pulse modulation signal of pulse compression radar,but current IFM system can not detect this signal,at the same time overlapping signal can not be detected in IFM system. So based on IFM system,this paper analyzes theoretical output of single and overlapping LFM signal through IFM system. On the basis of this,an improved idea and algorithm are put forward,that can estimate parameters of overlapping LFM signal. New method uses Analog To Digital Converter (ADC)parts to make quantitative and continuous time sampling to frontier un-overlapping output value of the two orthogonal channel (I/Q),and gets discrete frequency values of one signal,at last used LMS algorithm to estimate initial frequency and frequency modulation slope of this LMF single. Based on this,according to the overlapping output values of I/Q, parameters of another signal is estimated. Simulation validation of Matlab/Simulink show that this method can estimate parameters of two overlapping singles.