工业安全与环保
工業安全與環保
공업안전여배보
Industrial Safety and Environmental Protection
2015年
9期
17-19
,共3页
沥青烟电除尘器%气流均布%数值仿真%计算流体动力学
瀝青煙電除塵器%氣流均佈%數值倣真%計算流體動力學
력청연전제진기%기류균포%수치방진%계산류체동역학
asphalt fume electrostatic precipitator%airflow numerical simulation%computational fluid dynamics
为了保证沥青烟电除尘器的捕集效率,优化其本体结构设计,明确其气流均布板的布置是否合理,对其本体内的气流状态做了三维数值仿真研究。首先建立了 k-ε双方程模型,然后在ANSYS平台中用有限体积法对气流空间进行网格划分,最后用解压力耦合方程的半隐式算法进行仿真计算。仿真结果显示,除尘器本体内气流分布正常,说明设计的沥青烟电除尘器本体结构合理,为进一步优化其本体结构提供了依据,也为其在较高除尘效率下运行提供了帮助。
為瞭保證瀝青煙電除塵器的捕集效率,優化其本體結構設計,明確其氣流均佈闆的佈置是否閤理,對其本體內的氣流狀態做瞭三維數值倣真研究。首先建立瞭 k-ε雙方程模型,然後在ANSYS平檯中用有限體積法對氣流空間進行網格劃分,最後用解壓力耦閤方程的半隱式算法進行倣真計算。倣真結果顯示,除塵器本體內氣流分佈正常,說明設計的瀝青煙電除塵器本體結構閤理,為進一步優化其本體結構提供瞭依據,也為其在較高除塵效率下運行提供瞭幫助。
위료보증력청연전제진기적포집효솔,우화기본체결구설계,명학기기류균포판적포치시부합리,대기본체내적기류상태주료삼유수치방진연구。수선건립료 k-ε쌍방정모형,연후재ANSYS평태중용유한체적법대기류공간진행망격화분,최후용해압력우합방정적반은식산법진행방진계산。방진결과현시,제진기본체내기류분포정상,설명설계적력청연전제진기본체결구합리,위진일보우화기본체결구제공료의거,야위기재교고제진효솔하운행제공료방조。
In order to ensure the collection efficiency of the electrostatic precipitator (ESP) for asphalt smoke ,it is neces-sary to optimize the body’s structure ,especially to know if the setup of distribution board is reasonable or not and so an air-flow numerical simulation on ESP body is done .Firstly the k-εdouble equation model is established ,then the finite vol-ume method is used to conduct the division grid of the air space in the ANSYS platform and lastly the numerical result through semi implicit method for pressure coupled equations algorithm is calculated .The simulation result show that the body air distribution is normal and it illustrates the body structure of the ESP is reasonable ,which can provide references for the optimization of its structure and help it operate effectively .