电加工与模具
電加工與模具
전가공여모구
Electromachining & Mould
2015年
5期
38-42,51
,共6页
李志朝%连芩%贾书海%吕毅%李涤尘
李誌朝%連芩%賈書海%呂毅%李滌塵
리지조%련금%가서해%려의%리조진
光固化水凝胶%喷墨%模型%三维方块
光固化水凝膠%噴墨%模型%三維方塊
광고화수응효%분묵%모형%삼유방괴
photo-curable hydrogel%inkjet printing%model%three-dimensional block
针对可光固化水凝胶成形速度快、粘度低的特点,提出了一种包括电磁阀喷头系统和光源系统的喷墨式打印方法,能克服以成缸溶液直接扫描加工多种可光固化水凝胶存在的加工复杂、材料易被污染和损耗高等缺点。用光学显微镜对固化液滴和堆积直线进行了测量和分析,结果表明:随着喷头孔径和压力的增大,液滴固化直径增大;当浓度>30%时,随着浓度的增大,液滴固化直径减小。同时,建立了液滴固化和液滴堆积成形模型,形成的直线宽度不大于单个液滴的直径且宽度均匀。
針對可光固化水凝膠成形速度快、粘度低的特點,提齣瞭一種包括電磁閥噴頭繫統和光源繫統的噴墨式打印方法,能剋服以成缸溶液直接掃描加工多種可光固化水凝膠存在的加工複雜、材料易被汙染和損耗高等缺點。用光學顯微鏡對固化液滴和堆積直線進行瞭測量和分析,結果錶明:隨著噴頭孔徑和壓力的增大,液滴固化直徑增大;噹濃度>30%時,隨著濃度的增大,液滴固化直徑減小。同時,建立瞭液滴固化和液滴堆積成形模型,形成的直線寬度不大于單箇液滴的直徑且寬度均勻。
침대가광고화수응효성형속도쾌、점도저적특점,제출료일충포괄전자벌분두계통화광원계통적분묵식타인방법,능극복이성항용액직접소묘가공다충가광고화수응효존재적가공복잡、재료역피오염화손모고등결점。용광학현미경대고화액적화퇴적직선진행료측량화분석,결과표명:수착분두공경화압력적증대,액적고화직경증대;당농도>30%시,수착농도적증대,액적고화직경감소。동시,건립료액적고화화액적퇴적성형모형,형성적직선관도불대우단개액적적직경차관도균균。
Owing to the fast forming speed and low viscosity of the photo-curable hydrogel ,an inkjet printing method with electromagnetic valve sprinkler and lighting systems was proposed ,which can overcome the processing complexity ,the high loss and easy pollution of materials in printing various hydrogels by the direct scanning of the cylinder solution. Solidified droplets and the accumulation of line are measured by optical microscope ,the results show that as the nozzle aperture and pressure increases,the droplets solidify diameter increases. And when the concentration is greater than 30 % and increases,the droplet diameter decreases. By establishing the droplets solidify and droplet deposition modeling model,the width of forming a straight line is not greater than a single droplet′s diameter and reflects its uniformity.