中国有色金属学报
中國有色金屬學報
중국유색금속학보
The Chinese Journal of Nonferrous Metals
2015年
10期
2695-2706
,共12页
赵运兴%王薪%刘军%黄岚%江亮
趙運興%王薪%劉軍%黃嵐%江亮
조운흥%왕신%류군%황람%강량
镍基单晶高温合金%热处理%高温氧化%高温拉伸
鎳基單晶高溫閤金%熱處理%高溫氧化%高溫拉伸
얼기단정고온합금%열처리%고온양화%고온랍신
nickel-base single crystal superalloy%heat treatment%high temperature oxidation%high temperature tensile
采用高通量的合金设计方法设计一种新型镍基单晶高温合金CSU-B2,并对该合金进行了一系列的研究。结果表明:该合金在铸态下树枝晶分布均匀,枝晶间距约为500μm,没有三次枝晶出现。通过对合金进行固溶和时效处理,合金中的γ′析出相呈现方块状,平均颗粒尺寸为0.5~0.8μm。在1100和1150℃下对合金的抗氧化性能进行研究发现,试样单位面积质量随时间的变化遵循类抛物线的规律,在氧化层的下面都存在着γ′相消失的区域。最后对合金的高温拉伸性能进行了表征,在760℃时,合金的屈服强度为706 MPa;在980℃时,合金的屈服强度为484 MPa。在两个温度下,试样的断裂为两种不同的机制。
採用高通量的閤金設計方法設計一種新型鎳基單晶高溫閤金CSU-B2,併對該閤金進行瞭一繫列的研究。結果錶明:該閤金在鑄態下樹枝晶分佈均勻,枝晶間距約為500μm,沒有三次枝晶齣現。通過對閤金進行固溶和時效處理,閤金中的γ′析齣相呈現方塊狀,平均顆粒呎吋為0.5~0.8μm。在1100和1150℃下對閤金的抗氧化性能進行研究髮現,試樣單位麵積質量隨時間的變化遵循類拋物線的規律,在氧化層的下麵都存在著γ′相消失的區域。最後對閤金的高溫拉伸性能進行瞭錶徵,在760℃時,閤金的屈服彊度為706 MPa;在980℃時,閤金的屈服彊度為484 MPa。在兩箇溫度下,試樣的斷裂為兩種不同的機製。
채용고통량적합금설계방법설계일충신형얼기단정고온합금CSU-B2,병대해합금진행료일계렬적연구。결과표명:해합금재주태하수지정분포균균,지정간거약위500μm,몰유삼차지정출현。통과대합금진행고용화시효처리,합금중적γ′석출상정현방괴상,평균과립척촌위0.5~0.8μm。재1100화1150℃하대합금적항양화성능진행연구발현,시양단위면적질량수시간적변화준순류포물선적규률,재양화층적하면도존재착γ′상소실적구역。최후대합금적고온랍신성능진행료표정,재760℃시,합금적굴복강도위706 MPa;재980℃시,합금적굴복강도위484 MPa。재량개온도하,시양적단렬위량충불동적궤제。
A new nickel-base single crystal superalloy named CSU-B2 was designed by high-throughput alloy design method and a series of investigations were done to characterize the superalloy. The results show that the primary dendrites are uniformly distributed and the spacing size in the as-cast alloy is about 500 μm, where tertiary dendrite is absent. After solution and ageing treatments, theγ′prime precipitates are cuboidal-shaped and the average size is 0.5?0.8μm. The oxidation-resistance property of the new alloy is evaluated at 1100 and 1150℃, the results show that the oxide growth of the new alloy obeys the parabolic law for both under isothermal and cyclic oxidation, and there both have aγ′free zone under the oxide scale. The yield strengths under the temperature of 760 and 980℃are measured to be 706 and 484 MPa, respectively, and two different mechanisms govern the failure processes.