CAJ | 학술논문

为提高气送式集排器的兼用性和精量控制供种量,设计了一种油麦兼用型倾斜锥孔轮式供种装置.该文阐述了油麦兼用型供种装置的工作原理,确定了其主要结构参数,构建了充种和供种过程种群微段的力学模型;台架试验研究了型孔结构、转速和锥孔轮数量对供种速率及其稳定性变异系数和破损率的影响.结果表明:倾角为 20°的锥柱状型孔的供种性能较优,油菜、小麦的供种速率稳定性变异系数分别低于1.0%和1.1%,破损率均低于0.1%;转速为10~60 r/min时,供种速率随转速增加而增加,其稳定性变异系数呈先降后升的趋势,供种油菜、小麦较优转速范围分别为10~40 r/min和20~50 r/min;油菜、小麦的供种速率范围分别为28~450 g/min和95~770 g/min,以锥孔轮数量和转速为自变量建立了二次多元回归供种速率预测模型,模型验证的试验值与理论值的偏差在 5%以内.该研究提出的倾斜锥柱状型孔交错排布和组合式锥孔轮的结构可实现油菜、小麦兼用供种及变量调节供种速率,为油麦兼用型气送式集排器适应不同作业幅宽播种提供了依据.
위제고기송식집배기적겸용성화정량공제공충량,설계료일충유맥겸용형경사추공륜식공충장치.해문천술료유맥겸용형공충장치적공작원리,학정료기주요결구삼수,구건료충충화공충과정충군미단적역학모형;태가시험연구료형공결구、전속화추공륜수량대공충속솔급기은정성변이계수화파손솔적영향.결과표명:경각위 20°적추주상형공적공충성능교우,유채、소맥적공충속솔은정성변이계수분별저우1.0%화1.1%,파손솔균저우0.1%;전속위10~60 r/min시,공충속솔수전속증가이증가,기은정성변이계수정선강후승적추세,공충유채、소맥교우전속범위분별위10~40 r/min화20~50 r/min;유채、소맥적공충속솔범위분별위28~450 g/min화95~770 g/min,이추공륜수량화전속위자변량건립료이차다원회귀공충속솔예측모형,모형험증적시험치여이론치적편차재 5%이내.해연구제출적경사추주상형공교착배포화조합식추공륜적결구가실현유채、소맥겸용공충급변량조절공충속솔,위유맥겸용형기송식집배기괄응불동작업폭관파충제공료의거.
Wheat and rapeseed are the major grain and oil crop in China and their sowing dates are closer. Seed feeding device is the core component of air-assisted centralized metering device which is capable of handling a wide range of seeds with different sizes and shapes. In order to improve the versatility and use efficiency of air-assisted centralized metering device and adjust the feeding rate accurately, the seed feeding device for rapeseed and wheat with staggered arrangement shape hole and combined conical-hole unit was designed. The problems of pulsing phenomenon due to outer grooved wheel metering device of the centralized pneumatic planter and high damage rate of mechanical metering device for rapeseed needed to be solved, and the structure of staggered arrangement shape hole could keep seeding consciously and uniformly. The seed feeding operation included seed filling, carrying and feeding process. The main structural parameters of shape hole and conical-hole unit were determined in this research. These included length, width, depth and cone angle of shape hole which were 8.0 mm, 5.0 mm, 4.0 mm and 14°, respectively. The diameter and number of shape holes in each conical-hole unit were 80 mm and 60, respectively. Mechanical models were established to estimate the seed filling and feeding process. It demonstrated that seed filling and throwing performance were better under the inclined angle of 13.75°-21.20°. Bench experiments were carried out in the seed metering laboratory of Huazhong Agricultural University in 2015 by using Huayouza 62 and Zhengmai 9023 as materials. The experimental factors were inclined angle (0°-30°) with 4 levels and rotational speed (10-60 r/min) with 6 levels in single-factor test. Two-factor full factorial test was designed with number of conical-hole unit (1-6) and rotational speed. The objective values were seed feeding rate, coefficient variation of seed feeding rate and damage rate. The results showed that: 1) The conical shape hole with inclined angleresulted in a better seed feeding performance. When the rotational speed of seed feeding device was 10-30 r/min, the seed feeding performance of conical shape hole with 20° inclined angle was better than that of others. The coefficients of variation of seed feeding rate for rapeseed and wheat were not more than 1.0% and 1.1%, respectively, and their damage rates were both less than 0.1%. 2) With the increase of rotational speed in the range of 10-60 r/min, the seed feeding rate increased gradually, while the coefficient of variation of seed feeding rate decreased first and then rose up. The lowest coefficients of variation of seed feeding rate for rapeseed and wheat were recorded at 20 and 30 r/min, respectively. Thus, the optimum rotational speeds which resulted in the coefficient of variation less than 1.0% for rapeseed and wheat were 10-40 and 20-50 r/min, respectively. 3) The ranges of seed feeding rate for rapeseed and wheat were 28-450 and 95-770 g/min, respectively when number of conical-hole unit and rotational speed changed. The wide range of seed feeding rate could be adjusted to meet the requirements of different sowing width and high operating speed. The quadratic regression prediction models were established to describe different seed feeding rate for rapeseed and wheat. The models were verified with different forward velocity of Dongfanghong-LX854 tractor. The relative errors between experimental and simulated results in seed feeding rate were smaller than 5%. It indicates that the models can predict seed feeding rate and calculate the number of conical-hole unit and rotational speed accurately. The staggered arrangement shape hole and combined conical-hole unit can realize the adjustment of seed feeding rate in wide range for rapeseed and wheat and the damage rate is reduced significantly. The results provide technical support for the adjustment of different sowing width of air-assisted centralized metering device for rapeseed and wheat.