铁道建筑
鐵道建築
철도건축
Railway Engineering
2015年
10期
160-163
,共4页
白东辉%程建平%马战国%李伟
白東輝%程建平%馬戰國%李偉
백동휘%정건평%마전국%리위
重载铁路%小半径曲线%钢轨润滑%钢轨侧磨%润滑周期
重載鐵路%小半徑麯線%鋼軌潤滑%鋼軌側磨%潤滑週期
중재철로%소반경곡선%강궤윤활%강궤측마%윤활주기
Heavy haul railway%Small radius curve%Rail lubrication%Side wear of rail%Lubrication cycle
为比选出适用于朔黄重载铁路的曲线钢轨润滑剂,确定曲线钢轨润滑周期,进行了室内试验和现场验证试验.室内试验采用 MM-200 磨损试验机模拟重载铁路轮轨接触,分800,1 500,2 000 N共3 种荷载工况,分别对4 种润滑剂进行了摩擦性能试验.试验结果表明,济南三新干式润滑剂在1 500 N 和2 000 N荷载下减磨效果明显.针对比选出的两种润滑剂,在 R600 m 曲线进行了现场对比试验,通过总重达到224 MGt时,济南三新干式润滑剂的减磨效果明显,其平均侧磨量减少54. 4%.朔黄铁路在目前运输条件下,济南三新干式润滑剂的润滑周期应控制在12 h以内,即每天涂敷2 次.
為比選齣適用于朔黃重載鐵路的麯線鋼軌潤滑劑,確定麯線鋼軌潤滑週期,進行瞭室內試驗和現場驗證試驗.室內試驗採用 MM-200 磨損試驗機模擬重載鐵路輪軌接觸,分800,1 500,2 000 N共3 種荷載工況,分彆對4 種潤滑劑進行瞭摩抆性能試驗.試驗結果錶明,濟南三新榦式潤滑劑在1 500 N 和2 000 N荷載下減磨效果明顯.針對比選齣的兩種潤滑劑,在 R600 m 麯線進行瞭現場對比試驗,通過總重達到224 MGt時,濟南三新榦式潤滑劑的減磨效果明顯,其平均側磨量減少54. 4%.朔黃鐵路在目前運輸條件下,濟南三新榦式潤滑劑的潤滑週期應控製在12 h以內,即每天塗敷2 次.
위비선출괄용우삭황중재철로적곡선강궤윤활제,학정곡선강궤윤활주기,진행료실내시험화현장험증시험.실내시험채용 MM-200 마손시험궤모의중재철로륜궤접촉,분800,1 500,2 000 N공3 충하재공황,분별대4 충윤활제진행료마찰성능시험.시험결과표명,제남삼신간식윤활제재1 500 N 화2 000 N하재하감마효과명현.침대비선출적량충윤활제,재 R600 m 곡선진행료현장대비시험,통과총중체도224 MGt시,제남삼신간식윤활제적감마효과명현,기평균측마량감소54. 4%.삭황철로재목전운수조건하,제남삼신간식윤활제적윤활주기응공제재12 h이내,즉매천도부2 차.
In order to determine the curve rail lubrication cycle and the most suitable curve rail lubrication for Shuohuang heavy haul railway,the laboratory and field experiments were carried out in this paper. M M-200 wear testing machine was used to simulate the rail/wheel contact of heavy haul railway and wear performance tests for 4 kinds of lubrication w ere conducted respectively under load condition of 800 N ,1 500 N and 2 000 N . T est results show ed that Jinan Sanxin dry lubricant presents obvious w ear reduction effect under load of 1 500 N and 2 000 N . For two kinds of selected lubricants,field comparison tests were made on R600 m curve rail. W hen the total weight reached 224 M Gt,Jinan Sanxin dry lubricant has obvious wear reduction effect,mean side wear of which was reduced by 54. 4%. Under current transport conditions of Shuohuang railway,lubrication cycle of Jinan Sanxin dry lubricant should be controlled within 12 h,which means coating 2 times a day.