橡胶科技
橡膠科技
상효과기
Rubber Science and Technology
2015年
9期
41-43
,共3页
叉车轮胎%结构设计%施工设计
扠車輪胎%結構設計%施工設計
차차륜태%결구설계%시공설계
forklift truck tire%structure design%construction design
介绍4.50-1210PR叉车轮胎的设计。结构设计:断面宽度116 mm,外直径546 mm,行驶面宽度104 mm,行驶面弧度高5.5 mm,断面水平轴位置(H1/H2)0.8615,胎圈着合直径304 mm,胎圈着合宽度76 mm,花纹深度11 mm。施工设计:胎面采用一方一块结构;胎体采用4层1680V1锦纶帘布,胎冠帘线角度(54±0.5)°,胎体安全倍数12;钢丝圈为单钢丝圈,钢丝排列方式为5×5,胎圈安全倍数7;成型采用半鼓式成型机,胎体帘布和胎面均采用套筒法成型。成品轮胎充气外缘尺寸、物理性能和胎冠帘线角度符合设计要求。
介紹4.50-1210PR扠車輪胎的設計。結構設計:斷麵寬度116 mm,外直徑546 mm,行駛麵寬度104 mm,行駛麵弧度高5.5 mm,斷麵水平軸位置(H1/H2)0.8615,胎圈著閤直徑304 mm,胎圈著閤寬度76 mm,花紋深度11 mm。施工設計:胎麵採用一方一塊結構;胎體採用4層1680V1錦綸簾佈,胎冠簾線角度(54±0.5)°,胎體安全倍數12;鋼絲圈為單鋼絲圈,鋼絲排列方式為5×5,胎圈安全倍數7;成型採用半鼓式成型機,胎體簾佈和胎麵均採用套筒法成型。成品輪胎充氣外緣呎吋、物理性能和胎冠簾線角度符閤設計要求。
개소4.50-1210PR차차륜태적설계。결구설계:단면관도116 mm,외직경546 mm,행사면관도104 mm,행사면호도고5.5 mm,단면수평축위치(H1/H2)0.8615,태권착합직경304 mm,태권착합관도76 mm,화문심도11 mm。시공설계:태면채용일방일괴결구;태체채용4층1680V1금륜렴포,태관렴선각도(54±0.5)°,태체안전배수12;강사권위단강사권,강사배렬방식위5×5,태권안전배수7;성형채용반고식성형궤,태체렴포화태면균채용투통법성형。성품륜태충기외연척촌、물이성능화태관렴선각도부합설계요구。
In this paper, the design of 4.50-12 10PR forklift truck tire was described. In the structure design, the following parameters were taken: cross-sectional width 116 mm, overall diameter 546 mm, width of running surface 104 mm, height of running surface 5.5 mm, maximum width position of cross section (H1/H2) 0.8615, bead diameter 304 mm, bead width 76 mm, and tread pattern depth 11 mm. In the construction design, single piece tread with one formula was applied, 4 layers of 1680V1 nylon cord were used in the carcass ply, crown cord angle was set at(54 ± 0.5)°, the cascass safety factor was 12, single steel bead wire was adopted with arrangement of 5×5, and the bead safety factor was 7. The tire was built on semi-drum type building machine while the carcass ply and tread were molded using tube molding process. The testing results showed that the inlfated peripheral dimension and physical properties of the ifnished tire, and the crown cord angle met the design requirements.