中国电机工程学报
中國電機工程學報
중국전궤공정학보
Proceedings of the CSEE
2015年
21期
5592-5599
,共8页
李珍国%王江浩%高雪飞%方一鸣
李珍國%王江浩%高雪飛%方一鳴
리진국%왕강호%고설비%방일명
无刷直流电机%合成电流控制%双闭环调速系统%转矩脉动抑制%配合调制
無刷直流電機%閤成電流控製%雙閉環調速繫統%轉矩脈動抑製%配閤調製
무쇄직류전궤%합성전류공제%쌍폐배조속계통%전구맥동억제%배합조제
brushless DC motor (BLDCM)%resultant current control%double-loop speed control system%torque ripple reduction%cooperative modulation
具有非换相相电流反馈的无刷直流电机的传统双闭环调速系统,因非理想梯形波反电势和非理想方波相电流存在较大转矩脉动,该文引入正比于瞬时转矩的合成电流变量,并推导出每个扇区下的合成电流与非换相相电流之间的关系式,通过控制所需合成电流的对应非换相相电流,达到抑制转矩脉动的目的。此外,为了减小换相转矩脉动,采用一种基于PWM-on的新型调制方式。该调制方式在换相期间,三相将进行配合调制,通过计算给每一相分配不同的调制占空比,使开通相和关断相的电流变化率相等。所提转矩脉动抑制方法通过相应的 Matlab 仿真和数字信号处理驱动实验,验证了其可行性和有效性。
具有非換相相電流反饋的無刷直流電機的傳統雙閉環調速繫統,因非理想梯形波反電勢和非理想方波相電流存在較大轉矩脈動,該文引入正比于瞬時轉矩的閤成電流變量,併推導齣每箇扇區下的閤成電流與非換相相電流之間的關繫式,通過控製所需閤成電流的對應非換相相電流,達到抑製轉矩脈動的目的。此外,為瞭減小換相轉矩脈動,採用一種基于PWM-on的新型調製方式。該調製方式在換相期間,三相將進行配閤調製,通過計算給每一相分配不同的調製佔空比,使開通相和關斷相的電流變化率相等。所提轉矩脈動抑製方法通過相應的 Matlab 倣真和數字信號處理驅動實驗,驗證瞭其可行性和有效性。
구유비환상상전류반궤적무쇄직류전궤적전통쌍폐배조속계통,인비이상제형파반전세화비이상방파상전류존재교대전구맥동,해문인입정비우순시전구적합성전류변량,병추도출매개선구하적합성전류여비환상상전류지간적관계식,통과공제소수합성전류적대응비환상상전류,체도억제전구맥동적목적。차외,위료감소환상전구맥동,채용일충기우PWM-on적신형조제방식。해조제방식재환상기간,삼상장진행배합조제,통과계산급매일상분배불동적조제점공비,사개통상화관단상적전류변화솔상등。소제전구맥동억제방법통과상응적 Matlab 방진화수자신호처리구동실험,험증료기가행성화유효성。
In the traditional double closed-loop speed control system, the Brushless DC Motor with un-commutated phase current feedback has large torque ripple because of the non-ideal trapezoidal wave back EMF and non-ideal square wave phase currents. To overcome this defect, the relational expression between the resultant current and the un-commutated phase current under each sector is derived by introducing the resultant current which is proportional to the instantaneous torque, and then the torque ripple reduction can be achieved by controlling the un-commutated phase current which corresponds to the resultant current. In addition, to reduce the torque ripple in the commutation region, a new modulation method based on PWM-on is adopted. During the commutation region, three phases can be modulated cooperatively. And with this modulation method, the changing rate of currents in the upcoming phase can be controlled equally to that of the outgoing phase by distributing different modulation duty to each phase. Finally, results of Matlab simulations and experiments with DSP are presented to verify the feasibility and effectiveness of the proposed strategy.